Internet Engineering Task Force Audio/Video Transport Working Group INTERNET-DRAFT S. Casner draft-ietf-avt-rfc3555bis-part2-01.txt Packet Design Obsoletes: RFC 3555 (if approved) June 3, 2006 Expires: December 3, 2006 Media Type Registration of Payload Formats in the RTP Profile for Audio and Video Conferences Status of this Memo By submitting this Internet-Draft, each author represents that any applicable patent or other IPR claims of which he or she is aware have been or will be disclosed, and any of which he or she becomes aware will be disclosed, in accordance with Section 6 of BCP 79. Internet-Drafts are working documents of the Internet Engineering Task Force (IETF), its areas, and its working groups. Note that other groups may also distribute working documents as Internet-Drafts. Internet-Drafts are draft documents valid for a maximum of six months and may be updated, replaced, or obsoleted by other documents at any time. It is inappropriate to use Internet-Drafts as reference material or to cite them other than as "work in progress." The list of current Internet-Drafts can be accessed at http://www.ietf.org/ietf/1id-abstracts.txt The list of Internet-Draft Shadow Directories can be accessed at http://www.ietf.org/shadow.html. This Internet-Draft will expire on August 26, 2006. Copyright Notice Copyright (C) The Internet Society (2006). Abstract This document specifies media type registrations for the RTP payload formats defined in the RTP Profile for Audio and Video Conferences. Some of these may also be used for transfer modes other than RTP. Expires December 2006 [Page 1] Internet Draft draft-ietf-avt-rfc3555bis-part2-01.txt June 3, 2006 Table of Contents 1. Introduction .................................................. 3 1.1. IANA Considerations ...................................... 3 1.2. Terminology .............................................. 4 2. Registrations for "Audio/Video Profile" ....................... 4 2.1. Audio Type Registrations ................................. 4 2.2. Video Type Registrations ................................. 25 3. Changes from RFC 3555 ......................................... 26 4. Security Considerations ....................................... 26 5. References .................................................... 26 6. Author's Address .............................................. 27 7. Intellectual Property Statement ............................... 28 8. Disclaimer of Validity ........................................ 28 9. Copyright Statement ........................................... 28 Expires December 2006 [Page 2] Internet Draft draft-ietf-avt-rfc3555bis-part2-01.txt June 3, 2006 1. Introduction This document updates the media type registrations initially specified in RFC 3555 for the RTP payload formats defined in the RTP Profile for Audio and Video Conferences, RFC 3551 [1], as subtypes under the "audio" and "video" media types. This document does not include media type registrations for the RTP payload formats that are referenced in RFC 3551 but defined in other RFCs. The media type registrations for those payload formats are intended to be updated by including them in revisions of the individual RFCs defining the payload formats. The media type registrations specified here conform to the updated template format and procedures in RFC 4288 [2] and RFC XXXX [3]. This update makes no technical changes in the registrations. Together with RFC XXXX, this document obsoletes RFC 3555. 1.1. IANA Considerations As a consequence of the generalized applicability of the media types registry as specified in RFC 4288, some changes in nomenclature are needed in the RTP Payload Format section of the registry. In the registry title "RTP Payload Format MIME types" and the introductory text, "MIME" should be changed to "media". "MIME" should be deleted from the table headings, leaving just "media type" and "subtype". This document updates the media type registrations listed below to conform to the revised registration format specified in RFC 4288 and RFC XXXX, so the reference for these media types should be changed from RFC 3555 to this document. Some media type registrations contained in RFC 3555 are omitted from this document; the existing registrations for those types continue to be valid until updated by other RFCs. There are no new registrations contained here. Expires December 2006 [Page 3] Internet Draft draft-ietf-avt-rfc3555bis-part2-01.txt June 3, 2006 audio/DVI4 audio/G722 audio/G723 audio/G726-16 audio/G726-24 audio/G726-32 audio/G726-40 audio/G728 audio/G729 audio/G729D audio/G729E audio/GSM audio/GSM-EFR audio/L8 audio/L16 audio/LPC audio/PCMA audio/PCMU audio/VDVI video/nv Media type audio/L16 was initially registered via RFC 2586 for transports other than RTP. That registration is incorporated here and augmented with additional information for RTP transport. 1.2. Terminology The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT", "SHOULD", "SHOULD NOT", "RECOMMENDED", "MAY", and "OPTIONAL" in this document are to be interpreted as described in RFC 2119 [4] and indicate requirement levels for implementations compliant with this specification. 2. Registrations for "Audio/Video Profile" In the following sections, the RTP payload formats defined in the RTP Profile for Audio and Video Conferences, RFC 3551 [1], are registered as media types. 2.1. Audio Type Registrations For most audio payload formats, the RTP timestamp clock rate is equal to the sampling rate. Some payload formats operate only at one fixed sampling rate, while others are adjustable. These audio formats also include the optional parameters "ptime", to specify the recommended length of time in milliseconds represented by Expires December 2006 [Page 4] Internet Draft draft-ietf-avt-rfc3555bis-part2-01.txt June 3, 2006 the media in a packet, and "maxptime", to specify the maximum amount of media that can be encapsulated in each packet, expressed as time in milliseconds. The "ptime" and "maxptime" parameters are defined in the Session Description Protocol (SDP), RFC ZZZZ [5]. 2.1.1. Registration of Media Type audio/DVI4 Type name: audio Subtype name: DVI4 Required parameters: rate: The RTP timestamp clock rate, which is equal to the sampling rate. The typical rate is 8000, but other rates may be specified. Optional parameters: ptime, maxptime (see RFC ZZZZ) Encoding considerations: This media type is framed binary data (see Section 4.8 in RFC 4288). Security considerations: See Section 4 of RFC YYYY Interoperability considerations: none Published specification: RFC 3551 Applications which use this media type: Audio and video streaming and conferencing tools. Additional information: none Person & email address to contact for further information: Stephen Casner Intended usage: COMMON Restrictions on usage: This media type depends on RTP framing, and hence is only defined for transfer via RTP (RFC 3550 [6]). Transfer within other framing protocols is not defined at this time. Author: Stephen Casner Change controller: IETF Audio/Video Transport working group delegated from the Expires December 2006 [Page 5] Internet Draft draft-ietf-avt-rfc3555bis-part2-01.txt June 3, 2006 IESG. 2.1.2. Registration of Media Type audio/G722 Type name: audio Subtype name: G722 Required parameters: None Optional parameters: ptime, maxptime (see RFC ZZZZ) Encoding considerations: This media type is framed binary data (see Section 4.8 in RFC 4288). Security considerations: See Section 4 of RFC YYYY Interoperability considerations: none Published specification: RFC 3551 Applications which use this media type: Audio and video streaming and conferencing tools. Additional information: none Person & email address to contact for further information: Stephen Casner Intended usage: COMMON Restrictions on usage: This media type depends on RTP framing, and hence is only defined for transfer via RTP (RFC 3550). Transfer within other framing protocols is not defined at this time. Author: Stephen Casner Change controller: IETF Audio/Video Transport working group delegated from the IESG. 2.1.3. Registration of Media Type audio/G723 Type name: audio Expires December 2006 [Page 6] Internet Draft draft-ietf-avt-rfc3555bis-part2-01.txt June 3, 2006 Subtype name: G723 Required parameters: None Optional parameters: ptime, maxptime: see RFC ZZZZ bitrate: the data rate in kb/s used or preferred for the audio bit stream, with permissible values 5.3 or 6.3. If unspecified, the bitrate may change from frame to frame as indicated inband. annexa: indicates that Annex A, voice activity detection, is used or preferred. Permissible values are "yes" and "no" (without the quotes); "yes" is implied if this parameter is omitted. Encoding considerations: This media type is framed binary data (see Section 4.8 in RFC 4288). Security considerations: See Section 4 of RFC YYYY Interoperability considerations: none Published specification: RFC 3551 Applications which use this media type: Audio and video streaming and conferencing tools. Additional information: none Person & email address to contact for further information: Stephen Casner Intended usage: COMMON Restrictions on usage: This media type depends on RTP framing, and hence is only defined for transfer via RTP (RFC 3550). Transfer within other framing protocols is not defined at this time. Author: Stephen Casner Change controller: IETF Audio/Video Transport working group delegated from the IESG. Expires December 2006 [Page 7] Internet Draft draft-ietf-avt-rfc3555bis-part2-01.txt June 3, 2006 2.1.4. Registration of Media Type audio/G726-16 Type name: audio Subtype name: G726-16 Required parameters: None Optional parameters: ptime, maxptime (see RFC ZZZZ) Encoding considerations: This media type is framed binary data (see Section 4.8 in RFC 4288). Security considerations: See Section 4 of RFC YYYY Interoperability considerations: none Published specification: RFC 3551 Applications which use this media type: Audio and video streaming and conferencing tools. Additional information: none Person & email address to contact for further information: Stephen Casner Intended usage: COMMON Restrictions on usage: This media type depends on RTP framing, and hence is only defined for transfer via RTP (RFC 3550). Transfer within other framing protocols is not defined at this time. Author: Stephen Casner Change controller: IETF Audio/Video Transport working group delegated from the IESG. 2.1.5. Registration of Media Type audio/G726-24 Type name: audio Subtype name: G726-24 Expires December 2006 [Page 8] Internet Draft draft-ietf-avt-rfc3555bis-part2-01.txt June 3, 2006 Required parameters: None Optional parameters: ptime, maxptime (see RFC ZZZZ) Encoding considerations: This media type is framed binary data (see Section 4.8 in RFC 4288). Security considerations: See Section 4 of RFC YYYY Interoperability considerations: none Published specification: RFC 3551 Applications which use this media type: Audio and video streaming and conferencing tools. Additional information: none Person & email address to contact for further information: Stephen Casner Intended usage: COMMON Restrictions on usage: This media type depends on RTP framing, and hence is only defined for transfer via RTP (RFC 3550). Transfer within other framing protocols is not defined at this time. Author: Stephen Casner Change controller: IETF Audio/Video Transport working group delegated from the IESG. 2.1.6. Registration of Media Type audio/G726-32 Type name: audio Subtype name: G726-32 Required parameters: None Optional parameters: ptime, maxptime (see RFC ZZZZ) Encoding considerations: This media type is framed binary data (see Section 4.8 in RFC Expires December 2006 [Page 9] Internet Draft draft-ietf-avt-rfc3555bis-part2-01.txt June 3, 2006 4288). Security considerations: See Section 4 of RFC YYYY Interoperability considerations: none Published specification: RFC 3551 Applications which use this media type: Audio and video streaming and conferencing tools. Additional information: none Person & email address to contact for further information: Stephen Casner Intended usage: COMMON Restrictions on usage: This media type depends on RTP framing, and hence is only defined for transfer via RTP (RFC 3550). Transfer within other framing protocols is not defined at this time. Author: Stephen Casner Change controller: IETF Audio/Video Transport working group delegated from the IESG. 2.1.7. Registration of Media Type audio/G726-40 Type name: audio Subtype name: G726-40 Required parameters: None Optional parameters: ptime, maxptime (see RFC ZZZZ) Encoding considerations: This media type is framed binary data (see Section 4.8 in RFC 4288). Security considerations: See Section 4 of RFC YYYY Interoperability considerations: none Expires December 2006 [Page 10] Internet Draft draft-ietf-avt-rfc3555bis-part2-01.txt June 3, 2006 Published specification: RFC 3551 Applications which use this media type: Audio and video streaming and conferencing tools. Additional information: none Person & email address to contact for further information: Stephen Casner Intended usage: COMMON Restrictions on usage: This media type depends on RTP framing, and hence is only defined for transfer via RTP (RFC 3550). Transfer within other framing protocols is not defined at this time. Author: Stephen Casner Change controller: IETF Audio/Video Transport working group delegated from the IESG. 2.1.8. Registration of Media Type audio/G728 Type name: audio Subtype name: G728 Required parameters: None Optional parameters: ptime, maxptime (see RFC ZZZZ) Encoding considerations: This media type is framed binary data (see Section 4.8 in RFC 4288). Security considerations: See Section 4 of RFC YYYY Interoperability considerations: none Published specification: RFC 3551 Applications which use this media type: Audio and video streaming and conferencing tools. Expires December 2006 [Page 11] Internet Draft draft-ietf-avt-rfc3555bis-part2-01.txt June 3, 2006 Additional information: none Person & email address to contact for further information: Stephen Casner Intended usage: COMMON Restrictions on usage: This media type depends on RTP framing, and hence is only defined for transfer via RTP (RFC 3550). Transfer within other framing protocols is not defined at this time. Author: Stephen Casner Change controller: IETF Audio/Video Transport working group delegated from the IESG. 2.1.9. Registration of Media Type audio/G729 Type name: audio Subtype name: G729 Required parameters: None Optional parameters: ptime, maxptime: see RFC ZZZZ annexb: indicates that Annex B, voice activity detection, is used or preferred. Permissible values are "yes" and "no" (without the quotes); "yes" is implied if this parameter is omitted. Encoding considerations: This media type is framed binary data (see Section 4.8 in RFC 4288). Security considerations: See Section 4 of RFC YYYY Interoperability considerations: none Published specification: RFC 3551 Applications which use this media type: Audio and video streaming and conferencing tools. Expires December 2006 [Page 12] Internet Draft draft-ietf-avt-rfc3555bis-part2-01.txt June 3, 2006 Additional information: none Person & email address to contact for further information: Stephen Casner Intended usage: COMMON Restrictions on usage: This media type depends on RTP framing, and hence is only defined for transfer via RTP (RFC 3550). Transfer within other framing protocols is not defined at this time. Author: Stephen Casner Change controller: IETF Audio/Video Transport working group delegated from the IESG. 2.1.10. Registration of Media Type audio/G729D Type name: audio Subtype name: G729D Required parameters: None Optional parameters: ptime, maxptime: see RFC ZZZZ annexb: indicates that Annex B, voice activity detection, is used or preferred. Permissible values are "yes" and "no" (without the quotes); "yes" is implied if this parameter is omitted. Encoding considerations: This media type is framed binary data (see Section 4.8 in RFC 4288). Security considerations: See Section 4 of RFC YYYY Interoperability considerations: none Published specification: RFC 3551 Applications which use this media type: Audio and video streaming and conferencing tools. Expires December 2006 [Page 13] Internet Draft draft-ietf-avt-rfc3555bis-part2-01.txt June 3, 2006 Additional information: none Person & email address to contact for further information: Stephen Casner Intended usage: COMMON Restrictions on usage: This media type depends on RTP framing, and hence is only defined for transfer via RTP (RFC 3550). Transfer within other framing protocols is not defined at this time. Author: Stephen Casner Change controller: IETF Audio/Video Transport working group delegated from the IESG. 2.1.11. Registration of Media Type audio/G729E Type name: audio Subtype name: G729E Required parameters: None Optional parameters: ptime, maxptime: see RFC ZZZZ annexb: indicates that Annex B, voice activity detection, is used or preferred. Permissible values are "yes" and "no" (without the quotes); "yes" is implied if this parameter is omitted. Encoding considerations: This media type is framed binary data (see Section 4.8 in RFC 4288). Security considerations: See Section 4 of RFC YYYY Interoperability considerations: none Published specification: RFC 3551 Applications which use this media type: Audio and video streaming and conferencing tools. Expires December 2006 [Page 14] Internet Draft draft-ietf-avt-rfc3555bis-part2-01.txt June 3, 2006 Additional information: none Person & email address to contact for further information: Stephen Casner Intended usage: COMMON Restrictions on usage: This media type depends on RTP framing, and hence is only defined for transfer via RTP (RFC 3550). Transfer within other framing protocols is not defined at this time. Author: Stephen Casner Change controller: IETF Audio/Video Transport working group delegated from the IESG. 2.1.12. Registration of Media Type audio/GSM Type name: audio Subtype name: GSM Required parameters: None Optional parameters: ptime, maxptime (see RFC ZZZZ) Encoding considerations: This media type is framed binary data (see Section 4.8 in RFC 4288). Security considerations: See Section 4 of RFC YYYY Interoperability considerations: none Published specification: RFC 3551 Applications which use this media type: Audio and video streaming and conferencing tools. Additional information: none Person & email address to contact for further information: Stephen Casner Expires December 2006 [Page 15] Internet Draft draft-ietf-avt-rfc3555bis-part2-01.txt June 3, 2006 Intended usage: COMMON Restrictions on usage: This media type depends on RTP framing, and hence is only defined for transfer via RTP (RFC 3550). Transfer within other framing protocols is not defined at this time. Author: Stephen Casner Change controller: IETF Audio/Video Transport working group delegated from the IESG. 2.1.13. Registration of Media Type audio/GSM-EFR Type name: audio Subtype name: GSM-EFR Required parameters: None Optional parameters: ptime, maxptime (see RFC ZZZZ) Encoding considerations: This media type is framed binary data (see Section 4.8 in RFC 4288). Security considerations: See Section 4 of RFC YYYY Interoperability considerations: none Published specification: RFC 3551 Applications which use this media type: Audio and video streaming and conferencing tools. Additional information: none Person & email address to contact for further information: Stephen Casner Intended usage: COMMON Restrictions on usage: This media type depends on RTP framing, and hence is only defined for transfer via RTP (RFC 3550). Transfer within other framing protocols is not defined at this time. Expires December 2006 [Page 16] Internet Draft draft-ietf-avt-rfc3555bis-part2-01.txt June 3, 2006 Author: Stephen Casner Change controller: IETF Audio/Video Transport working group delegated from the IESG. 2.1.14. Registration of Media Type audio/L8 Type name: audio Subtype name: L8 Required parameters: rate: the RTP timestamp clock rate Optional parameters: channels: how many audio streams are interleaved -- defaults to 1; stereo would be 2, etc. Interleaving takes place between individual one-byte samples. The channel order is as specified in RFC 3551. ptime, maxptime: see RFC ZZZZ Encoding considerations: This media type is framed binary data (see Section 4.8 in RFC 4288). Security considerations: See Section 4 of RFC YYYY Interoperability considerations: none Published specification: RFC 3551 Applications which use this media type: Audio and video streaming and conferencing tools. Additional information: none Person & email address to contact for further information: Stephen Casner Intended usage: COMMON Restrictions on usage: This media type depends on RTP framing, and hence is only defined for transfer via RTP (RFC 3550). Transfer within other framing protocols is not defined at this time. Expires December 2006 [Page 17] Internet Draft draft-ietf-avt-rfc3555bis-part2-01.txt June 3, 2006 Author: Stephen Casner Change controller: IETF Audio/Video Transport working group delegated from the IESG. 2.1.15. Registration of Media Type audio/L16 Media type audio/L16 was initially registered via RFC 2586 for transports other than RTP. That registration is incorporated here and augmented with additional information for RTP transport. Type name: audio Subtype name: L16 Required parameters rate: number of samples per second -- For non-RTP transport, the permissible values for rate are 8000, 11025, 16000, 22050, 24000, 32000, 44100, and 48000 samples per second. For RTP transport, other values are permissible but the aforementioned values are RECOMMENDED. For RTP, the rate parameter indicates the RTP timestamp clock rate, which is equal to the sample rate. Optional parameters channels: how many audio streams are interleaved -- defaults to 1; stereo would be 2, etc. Interleaving takes place between individual two-byte samples. The channel order is as specified in RFC 3551 unless a channel-order parameter is also present. emphasis: analog preemphasis applied to the signal before quantization. The only emphasis value defined here is emphasis=50-15 to indicate the 50/15 microsecond preemphasis used with Compact Disks. This parameter MUST be omitted if no analog preemphasis was applied. Note that this is a stream property parameter, not a receiver configuration parameter. Thus, if parameters are negotiated, it may not be possible for the sender to comply with a receiver request for a particular setting. channel-order: specifies the sample interleaving order for multiple-channel audio streams (see RFC 3190 [7] Section 7). Permissible values are DV.LRLsRs, DV.LRCS, DV.LRCWo, DV.LRLsRsC, DV.LRLsRsCS, DV.LmixRmixTWoQ1Q2, DV.LRCWoLsRsLmixRmix, DV.LRCWoLs1Rs1Ls2Rs2, DV.LRCWoLsRsLcRc. Expires December 2006 [Page 18] Internet Draft draft-ietf-avt-rfc3555bis-part2-01.txt June 3, 2006 For interoperation with DV video systems, only a subset of these channel combinations is specified for use with 20-bit linear encoding in the DV video specification [8]; those are DV.LRLsRs, DV.LRCS, DV.LmixRmixTWoQ1Q2. This parameter MUST be omitted when the AIFF-C channel order convention (see RFC 3551) is in use. For RTP, ptime: RECOMMENDED duration of each packet in milliseconds. For RTP, maxptime: maximum duration of each packet in milliseconds. Encoding considerations Audio data is binary data, and must be encoded for non-binary transport; the Base64 encoding is suitable for Email. Note that audio data does not compress easily using lossless compression. Security considerations Audio data is believed to offer no security risks. See Section 4 of RFC YYYY. Interoperability considerations This type is compatible with the encoding used in the WAV (Microsoft Windows RIFF) and Apple AIFF union types, and with the public domain "sox" and "rateconv" programs. Published specification RFC 2586 for non-RTP transports, RFC 3551 for RTP Applications which use this media The public domain "sox" and "rateconv" programs accept this type. Magic number(s) : None File extension(s) : WAV L16 Macintosh file type code : AIFF Person to contact for further information Name : James Salsman E-mail : jps-L16@bovik.org Intended usage Common It is expected that many audio and speech applications will use this type. Already the most popular platforms provide Expires December 2006 [Page 19] Internet Draft draft-ietf-avt-rfc3555bis-part2-01.txt June 3, 2006 this type with the rate=11025 parameter referred to as "radio quality speech." Restrictions on usage In addition to file-based transfer methods, this type is also defined for transfer via RTP (RFC 3550). Author James Salsman for non-RTP transports. Stephen Casner for RTP transport. Change controller James Salsman for non-RTP transports. For RTP transport, IETF Audio/Video Transport working group delegated from the IESG. 2.1.16. Registration of Media Type audio/LPC Type name: audio Subtype name: LPC Required parameters: None Optional parameters: ptime, maxptime (see RFC ZZZZ) Encoding considerations: This media type is framed binary data (see Section 4.8 in RFC 4288). Security considerations: See Section 4 of RFC YYYY Interoperability considerations: none Published specification: RFC 3551 Applications which use this media type: Audio and video streaming and conferencing tools. Additional information: none Person & email address to contact for further information: Stephen Casner Intended usage: COMMON Restrictions on usage: This media type depends on RTP framing, and hence is only Expires December 2006 [Page 20] Internet Draft draft-ietf-avt-rfc3555bis-part2-01.txt June 3, 2006 defined for transfer via RTP (RFC 3550). Transfer within other framing protocols is not defined at this time. Author: Stephen Casner Change controller: IETF Audio/Video Transport working group delegated from the IESG. 2.1.17. Registration of Media Type audio/PCMA Type name: audio Subtype name: PCMA Required parameters: rate: The RTP timestamp clock rate, which is equal to the sampling rate. The typical rate is 8000, but other rates may be specified. Optional parameters: channels: how many audio streams are interleaved -- defaults to 1; stereo would be 2, etc. Interleaving takes place between individual one-byte samples. The channel order is as specified in RFC 3551. ptime, maxptime: see RFC ZZZZ Encoding considerations: This media type is framed binary data (see Section 4.8 in RFC 4288). Security considerations: See Section 4 of RFC YYYY Interoperability considerations: none Published specification: RFC 3551 Applications which use this media type: Audio and video streaming and conferencing tools. Additional information: none Person & email address to contact for further information: Stephen Casner Expires December 2006 [Page 21] Internet Draft draft-ietf-avt-rfc3555bis-part2-01.txt June 3, 2006 Intended usage: COMMON Restrictions on usage: This media type depends on RTP framing, and hence is only defined for transfer via RTP (RFC 3550). Transfer within other framing protocols is not defined at this time. Author: Stephen Casner Change controller: IETF Audio/Video Transport working group delegated from the IESG. 2.1.18. Registration of Media Type audio/PCMU Type name: audio Subtype name: PCMU Required parameters: rate: The RTP timestamp clock rate, which is equal to the sampling rate. The typical rate is 8000, but other rates may be specified. Optional parameters: channels: how many audio streams are interleaved -- defaults to 1; stereo would be 2, etc. Interleaving takes place between individual one-byte samples. The channel order is as specified in RFC 3551. ptime, maxptime: see RFC ZZZZ Encoding considerations: This media type is framed binary data (see Section 4.8 in RFC 4288). Security considerations: See Section 4 of RFC YYYY Interoperability considerations: none Published specification: RFC 3551 Applications which use this media type: Audio and video streaming and conferencing tools. Additional information: none Expires December 2006 [Page 22] Internet Draft draft-ietf-avt-rfc3555bis-part2-01.txt June 3, 2006 Person & email address to contact for further information: Stephen Casner Intended usage: COMMON Restrictions on usage: This media type depends on RTP framing, and hence is only defined for transfer via RTP (RFC 3550). Transfer within other framing protocols is not defined at this time. Author: Stephen Casner Change controller: IETF Audio/Video Transport working group delegated from the IESG. 2.1.19. Registration of Media Type audio/VDVI Type name: audio Subtype name: VDVI Required parameters: None Optional parameters: ptime, maxptime (see RFC ZZZZ) Encoding considerations: This media type is framed binary data (see Section 4.8 in RFC 4288). Security considerations: See Section 4 of RFC YYYY Interoperability considerations: none Published specification: RFC 3551 Applications which use this media type: Audio and video streaming and conferencing tools. Additional information: none Person & email address to contact for further information: Stephen Casner Intended usage: COMMON Expires December 2006 [Page 23] Internet Draft draft-ietf-avt-rfc3555bis-part2-01.txt June 3, 2006 Restrictions on usage: This media type depends on RTP framing, and hence is only defined for transfer via RTP (RFC 3550). Transfer within other framing protocols is not defined at this time. Author: Stephen Casner Change controller: IETF Audio/Video Transport working group delegated from the IESG. Expires December 2006 [Page 24] Internet Draft draft-ietf-avt-rfc3555bis-part2-01.txt June 3, 2006 2.2. Video Type Registrations For most video payload formats, including the one registered here, the RTP timestamp clock rate is always 90000 Hz, so the "rate" parameter is not applicable. Likewise, the "channel" parameter is not used with video, while "ptime" and "maxptime" could be but typically are not. 2.2.1. Registration of Media Type video/nv Type name: video Subtype name: nv Required parameters: None Optional parameters: None Encoding considerations: This media type is framed binary data (see Section 4.8 in RFC 4288). Security considerations: See Section 4 of RFC YYYY Interoperability considerations: none Published specification: RFC 3551 Applications which use this media type: Audio and video streaming and conferencing tools. Additional information: none Person & email address to contact for further information: Stephen Casner Intended usage: COMMON Restrictions on usage: This media type depends on RTP framing, and hence is only defined for transfer via RTP (RFC 3550). Transfer within other framing protocols is not defined at this time. Author: Stephen Casner Change controller: IETF Audio/Video Transport working group delegated from the IESG. Expires December 2006 [Page 25] Internet Draft draft-ietf-avt-rfc3555bis-part2-01.txt June 3, 2006 3. Changes from RFC 3555 RFC 3555 is obsoleted by the combination of RFC XXXX [3] and this document. RFC XXXX retains the specification of procedures and requirements from RFC 3555, while the media type registrations from RFC 3555 were extracted into this document. The media type registrations for the RTP payload formats that are referenced in RFC 3551 [1] but defined in other RFCs have been elided from this document because those registrations are intended to be updated by including them in revisions of the individual RFCs defining the payload formats. The media type registrations in this document have been updated to conform to the revised media type registration procedures in RFC 4288 [2] and RFC XXXX. Whereas RFC 3555 required the encoding considerations to specify transfer via RTP, that is now specified under restrictions on usage. The encoding considerations now warn that these types are framed binary data. The change controller is also now identified according to current conventions. The optional parameter "channels" was clarified for audio subtypes L8, PCMA, and PCMU. Finally, reference [8], which was missing from RFC 3555, has been corrected. 4. Security Considerations The media type registrations contained in this document do not by themselves impose security risks, but some may state security considerations specific to the particular registration. Several audio and video encodings are perfect for hiding data using steganography. The RTP specification, RFC 3550, provides security considerations for the transport of audio and video data over RTP, including the use of encryption where confidentiality is required. 5. References 5.1. Normative References [1] Schulzrinne, H. and S. Casner, "RTP Profile for Audio and Video Conferences with Minimal Control", RFC 3551, July 2003. [2] Freed, N. and J. Klensin, "Media Type Specifications and Registration Procedures", BCP 13, RFC 4288, December, 2005. [3] Casner, S., "Media Type Registration of RTP Payload Types", draft-ietf-avt-rfc3555bis-02.txt, February 2006. (Companion to this document, referenced herein as RFC XXXX). Expires December 2006 [Page 26] Internet Draft draft-ietf-avt-rfc3555bis-part2-01.txt June 3, 2006 [4] Bradner, S., "Key words for use in RFCs to Indicate Requirement Levels", BCP 14, RFC 2119, March 1997. [5] Handley, M., V. Jacobson and C. Perkins, "SDP: Session Description Protocol", draft-ietf-mmusic-sdp-new-26.txt, January 2006. (Approved for publication as Proposed Standard to obsolete RFC 2327, so this reference should be to the RFC when published and that number inserted where RFC ZZZZ appears in this document) [6] Schulzrinne, H., Casner, S., Frederick, R. and V. Jacobson, "RTP: A Transport Protocol for Real-Time Applications", RFC 3550, July 2003. [7] Kobayashi, K., Ogawa, A., Casner, S. and C. Bormann, "RTP Payload Format for 12-bit DAT Audio and 20- and 24-bit Linear Sampled Audio", RFC 3190, January 2002. 5.2. Informative References [8] IEC 61834, Helical-scan digital video cassette recording system using 6,35 mm magnetic tape for consumer use (525-60, 625-50, 1125-60 and 1250-50 systems), August 1998. [Note to RFC Editor: References in the media type registrations to RFC YYYY are to be replaced with the RFC number of this document itself. The purpose of the self-references is to make the registrations complete when extracted.] 6. Author's Address Stephen L. Casner Packet Design 3400 Hillview Avenue, Building 3 Palo Alto, CA 94304 United States Phone: +1 650 739-1843 EMail: casner@acm.org Expires December 2006 [Page 27] Internet Draft draft-ietf-avt-rfc3555bis-part2-01.txt June 3, 2006 7. Intellectual Property Statement The IETF takes no position regarding the validity or scope of any Intellectual Property Rights or other rights that might be claimed to pertain to the implementation or use of the technology described in this document or the extent to which any license under such rights might or might not be available; nor does it represent that it has made any independent effort to identify any such rights. Information on the procedures with respect to rights in RFC documents can be found in BCP 78 and BCP 79. Copies of IPR disclosures made to the IETF Secretariat and any assurances of licenses to be made available, or the result of an attempt made to obtain a general license or permission for the use of such proprietary rights by implementers or users of this specification can be obtained from the IETF on-line IPR repository at http://www.ietf.org/ipr. The IETF invites any interested party to bring to its attention any copyrights, patents or patent applications, or other proprietary rights that may cover technology that may be required to implement this standard. Please address the information to the IETF at ietf- ipr@ietf.org. 8. Disclaimer of Validity This document and the information contained herein are provided on an "AS IS" basis and THE CONTRIBUTOR, THE ORGANIZATION HE/SHE REPRESENTS OR IS SPONSORED BY (IF ANY), THE INTERNET SOCIETY AND THE INTERNET ENGINEERING TASK FORCE DISCLAIM ALL WARRANTIES, EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO ANY WARRANTY THAT THE USE OF THE INFORMATION HEREIN WILL NOT INFRINGE ANY RIGHTS OR ANY IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. 9. Copyright Statement Copyright (C) The Internet Society (2006). This document is subject to the rights, licenses and restrictions contained in BCP 78, and except as set forth therein, the authors retain all their rights. Expires December 2006 [Page 28]